1ton boiler how much is steam product

Hot water 1ton boiler how much is steam product deaerator works: the primary condensate from the low pressure heater (including supplement water) by adjusting the control valve inlet into the deaerator, hydrophobic mixed with the other in the brightest deaerator, upon spin discharging the film porous tube, skirt forming a water film, mixing and heat transfer and mass transfer with the bottom of the heating steam, water quickly reaches the saturated temperature at the operating pressure. In this case, most of oxygen and other gases in water are parsed substantially achieve the purpose of removing oxygen. The precipitated oxygen from the water and other gases are continuously removed from the outer tube with the top of the exhaust vapors deaerator.

Tai Chi, Jiaozuo City, Jiaozuo City Sports Center is one of important sports infrastructure, a total area of ​​11.73 hectares, held several international events. With strict management in Henan Province for air emissions of pollutants, Jiaozuo City, also launched the governance of coal-fired 1ton boiler how much is steam products, thermal power and other equipment. Jiaozuo Sports Center actively cooperate with municipal workers, took the lead from coal to gas activities, the serious pollution of the original extent of coal-fired boilers to replace gas boilers. Gas boiler cleaning binding understanding of the market, to achieve cooperation with the finalization fast boiler by providing a fast side 2.8MW integrally condensing gas hot water boiler (WNS2.8-1.0 / 95/70-YQ), it is used to Sports Center provides heating and hot water.

Talking about the reason for corrosion of 1ton boiler how much is steam product water most of our people still love the hot water boiler equipment, this situation makes the use of hot water boiler in our country more widely. But now the development of society, the hot water boiler in the course there have been some problems, these problems are largely due to the hot water boiler corrosion problems in the process of being used, there is erosion of our country's hot water development boiler subject to certain obstacles, so this requires appropriate measures against corrosion of hot water boiler arise in the course becomes more important. 1.1 1. The hot water boiler feed water causes corrosion in oxygen is well known that the relative increase in the use of hot water boiler is required to participate in appropriate water sources, and water in metal materials can lead to corrosion of the metal material phenomenon. And the water is from oxygen and hydrogen elements, and it also led to a large extent on the respective device corresponding metal oxide occurs during use, but also seriously affect the potential change of the metal surface. Since this will lead to excessive release of oxygen and the potential change of the metal surface, corrosion is exacerbated by the metal used in the process. Further studies in the respective hot water boiler is found there is a proportional relationship between the amount of leakage water capacity of the system in general and the boiler of the boiler, which is the ratio between the amount of leakage can not exceed the corresponding receiving system in a certain angle one percent of the amount of water. Thus during the welding of the boiler would need to fully consider these two points, the metal portion is welded tight, so that the integrity of the boiler to form a spacer. PH 1.2 Water circulating index gradually lower to a great extent, it will be associated such that the pH of the extent of corrosion of the metal object or exacerbate certain influence on the corrosion time. Hence the need for full consideration the degree of acid-base-site environment during the corresponding boiler equipment, but also that you maintain the appropriate level of pH can be maintained within the range set by the state. State PH value of the boiler is generally between predetermined environment 11 to 12, which means are above or below this value corresponding to the metal boiler corrosion, it will make the overall state of the further boiler takes place some changes. And the temperature of the hot water boiler are also corresponding requirements, generally require a temperature of hot water inside the hot water boiler is maintained at 95 degrees Celsius, but the amount of water to make the problem described earlier, if a boiler exceeds the predetermined replenishment the value will result in a corresponding change in the pH of the liquid inside the boiler occurs to a great extent, further affecting the normal operation of the boiler. 1.3 boiler action principle relatively fast flow rate through the boiler that the boiler is heated so that the liquid inside the boiler to achieve a state of heating, the boiler is further obtained that the normal operation. However, in the course of the entire hot water boiler is also a need to achieve appropriate control of the corresponding flow velocity. This is because in the course of excessive boiler or too slow water flow rate will make the crossing different corrosion occurs. When the water inside the boiler is too fast diffusion rate will lead to various substances contained inside the boiler becomes fast, this situation will be such that the angle of the underlying boiler corroded velocity have a certain upgrade. When the flow rate of the water inside the boiler is too slow, so that the gas boiler will overflow occurs, the overflow of these gases are typically adheres to the inner metal wall of the hot water boiler, so that the passage of time will occur in the corrosion of metal parts of the boiler The phenomenon.

3829, the 1ton boiler how much is steam product combustion boiler automation control automation level of development is very high, the end of the current boiler automation has become a new technology skills. Gas heating system implemented in a computer-controlled heating system, in this system calculates the parameters calculated for each parameter and the entire boiler heating system in a normal state by, theorizes that the boiler load condition, then according to this result adjust the boiler load conditions, which results boiler should be open, centralized control of the boiler. According to such automated systems, we can achieve automatic timing switch boiler boiler room in order to achieve circulation operation of the gas boiler, not only energy-saving heating boiler, and can effectively extend the life of the boiler.