boiler supplier

6ton hot water coal fuel boiler in bangladesh

Industrial 6ton hot water coal fuel boiler in bangladesh energy-saving technological transformation of existing problems in industrial boiler energy-saving technological transformation of Question 1, the lack of innovation, application of energy-saving boiler mature, molding technology and equipment, such as: increased flue gas heat recovery unit, blowers inverter , condensate recovery and other conventional energy-saving measures is essentially a general condition; and the need for structural changes in energy-saving measures, such as fractional bed combustion of coal and boiler furnace arch transformation techniques, etc., are rare; as transformation project new principle, a new device, oxyfuel technology, high temperature air combustion technology, spray pulverized coal combustion technology (+ supernatant layer combustion boiler combustion mode), condensing heat recovery technology, new energy technologies dust ash and water treatment equipment, is very few. In general, innovation is not enough, the technical content needs to be improved. 2, part of the boiler is not fully considered in the transformation process, but simply changing the burner, the combustion gas flow distribution and does not match the corresponding surface of the heating boiler, the boiler furnace wall insulation and sealing transformation. There is poor combustion boiler, insufficient output, higher exhaust temperature problem, can not achieve the purpose of energy saving. 3, the waste heat boiler using high temperature organic heat required for thermal processes, a boiler generally at 200 ℃ 300 ℃, the exhaust gas temperature of the boiler is usually too high, excessive. In order to meet requirements of energy saving, companies often mounted in the boiler backpass evaporator or a hot water tank, flue gas waste heat recovery, reducing the exhaust temperature. But most of the heat generated in the production process does not require little energy. 4, statistical analysis of experimental data shows that there are many problems inefficiencies run natural gas boiler. The main concern of automatic combustion control, early production debugging is not in place, and so on. Gas boiler gas and incomplete combustion abnormal increase in heat loss caused by high temperature exhaust gas is the direct cause of poor operating efficiency. However, the use of clean energy natural gas boiler, generally higher thermal efficiency, energy saving difficult. Corporate restructuring investment funds enthusiasm is not high.

The 6ton hot water coal fuel boiler in bangladesh must be sampled and tested to determine whether the appearance, quality, flash point, viscosity, acid value, carbon residue and moisture content of the heat transfer fluid are in conformity with the quality certificate provided by the heat transfer fluid production plant. At the same time, it also provides the basis for monitoring the change of medium quality in future operation. The heat transfer fluid will be injected into the furnace and expander with a pump to test the qualified heat transfer fluid. When the oil pump injects the heat transfer fluid into the system, it should check the furnace body again, use the heat equipment, the drain valve of the piping system, whether the oil release valve is closed or not, so as to avoid the loss of the heat transfer fluid. At the same time, open the exhaust valve one by one on the pipe and furnace body to remove the air until it is closed when there is an outflow. When When the oil level appears on the expander liquid level meter, the heat conduction liquid is stopped, then the circulating pump is started, and the cold circulation is carried out. The existing dry dust removal and wet desulfurization of boilers are not suitable for the treatment of high wet flue gas of coal water slurry, because the water vapor in the flue gas of coal water slurry is as high as 36%, and the water content of some coal water slurry is more than 40%. It is impossible to consider only dust and sulfur dioxide. Fangkuai Boiler Co., Ltd. has developed a dedusting product through multi-expert research and experiment, successfully using a large amount of water in coal water slurry flue gas as a carrier to capture dust and sulfur dioxide by cooling, reducing dewatering, and capturing dust and sulfur dioxide. Dust removal and Desulfurization reach the Best of Boiler Effect. The dust removal effect has reached the user's satisfaction. The welding of coal-fired boiler must be operated by the welder who holds the qualification certificate of welder for boiler pressure vessel. Welding dimensions meet the requirements of design drawings and process documents, weld height is not lower than base metal, smooth transition with base metal. There are no cracks, pores, craters and slag in the weld and heat affected zone of the oil-fired gas-fired boiler. Pipe hole weld edge bite depth not more than 0.5 mm, total length (sum of both sides) not exceeding 1 / 4 of tube perimeter, and not more than 40 mm. The boiler construction strictly complies with welding operation rules and other standards and relevant regulations, and makes a good record of construction welding. Record for the record.

Our jewelry processing company in the automotive production, many processes require energy, to be honest we really a headache on the choice of the 6ton hot water coal fuel boiler in bangladesh, thanks met specializes in the research and production of fast square boiler boiler! The purchase of two Taipower hot water boiler, tangible help us save a lot of costs. --customer feedback

Second, the clear purpose 6ton hot water coal fuel boiler in bangladesh "coal to gas"

1, while maintaining the original nominal parameters of the boiler (e.g., steam temperature, steam pressure, water temperature, etc.) remain unchanged, maintaining or improving output and efficiency of the boiler.

Related Information