boiler supplier

atmospheric direct fired cast iron module gas boiler

How to avoid the leakage of gas oil furnace and burner Selection Notice: Gas oil furnace, which is a heat transfer oil furnace, and that for us, but also the need to have a comprehensive knowledge and understanding of, because the only way in order to correct and rational use of this kind of atmospheric direct fired cast iron module boiler and make their own benefit. So, based on this, then, will explain the boiler-related knowledge, or some answers to common questions, so that we have the learning content, to supplement the expertise in this area. 1. Gas conducting oil furnace burners, which use imported brands, then in the selection, whether to the left margin? Gas conducting oil furnace burners, which use imported brands, then, in the selection of their work is to the left margin, because the only way to run the boiler at full capacity, the actual gas consumption smaller than the standard air consumption. And on this issue, the answer is yes.

How to improve the thermal oil atmospheric direct fired cast iron module boiler efficiency oil boiler thermal efficiency is a lot of users are taken into account, we believe that this issue is the direction of each used in the production of various types of oil boiler manufacturers have been in the study. Many users at the time of the oil furnace to operate, often in the actual production process, we found some new problems, but all the problems, the headache is higher oil boiler flue gas temperature, low thermal efficiency the phenomenon that a serious impact on our work, then how should we do to improve the thermal efficiency of it? need to understand this is to meet the low-temperature characteristics of the thermal oil comes as synthetic heat transfer oil. However, the vast majority of synthetic HTF complex biphenyls, benzene derivatives of both components, or a vapor of volatiles has strong carcinogenicity, it is strongly recommended to select customers conducting oil mineral oil products. Second, conducting oil products to meet the low temperature performance process, but also have a relatively high flash point required. In general, oil engineers suggest, low flash point not lower than the HTF opening 200 ℃. After a professional manufacturer of continuous research and improvement of its equipment, in order to improve its thermal efficiency was found to be increased oil boiler heating surface of the tail, say, air preheater and economizer. But when organic heat carrier furnace return temperature is high, you can not set the economizer, air preheater can only be set to alleviate the situation. So if the oil boiler and not other low-temperature heating system heat exchanger, then the only way to improve energy efficiency is adding air preheater. After adding air preheater can be a corresponding increase in the flow rate of heat-conducting oil, oil boiler in order to ensure safe, reliable and stable work, the thermal efficiency of the boiler plant with thermal oil will be a corresponding increase.

Behind honor, it is thousands of times persist and exploration. Keep trying, and failed to improve, we have a number of scientific and technological problems. The launch of China's first low nitrogen atmospheric direct fired cast iron module boiler and stable operation in 2014, Beijing Huairou APEC venue for the realization of "APEC blue" to contribute their part. Respond positively to national policy, contribute to the cause of environmental protection. Group focus on lower nitrogen oxide emissions, a low nitrogen introduction of multi-type boiler. Existing "Thalia", "Willie sharp" and other series, the successful implementation of nitrogen oxide emissions below 18 mg / cubic meter, this data is far below the national existing standards (such as the most stringent in Beijing the implementation of 30 mg / cubic meter standard), is widely used in national important organs of the CPC Central Authority, the national Tourism Bureau.

Gaz than steam atmospheric direct fired cast iron module boiler should be how to calculate? Q: ratio of gas steam boiler gaz simple algorithm is multiplied by the calorific value of coal and boiler efficiency is calculated by dividing this simple assumption does not heat to the steam boiler efficiency of 80%, coal calorific value 5500, if the amount of steam produced a ton of coal can be calculated as follows * 0.8 = 5500/600 = 7.3, ie: gaz ratio of 7.3 can be calculated simply, is this right? A: According to your argument: the amount of steam a ton of coal produced, commonly referred to as the evaporation rate of the fuel, commonly known as steam coal ratio. The calculation formula is: base received low calorific value of coal is then divided by multiplying the thermal efficiency of the boiler (steam heat feedwater minus heat). You said above is correct.

Related Information