boiler supplier

boiler manufacture in sonipat

Periodically check the boiler manufacture in sonipat with a certain pressure, because of the pressure, which can produce a high temperature well above 100 deg.] C, high-quality steam. But the pressure will have a certain risk, China has a dedicated quality control monitoring boiler inspection department, quality inspection once a year for the boiler, in order to ensure its good safety performance.

What issues should be considered in selecting Gas-fired boiler manufacture in sonipats

Compared with oil-fired or electric boilers, the advantages of gas-fired boilers, which attract more attention in the market, are obvious, and it is precisely because of this that gas-fired boilers can stand out from the market and be used by more people. So, what are some of the issues in the selection of high-quality and durable boiler equipment that users need to focus on?

18-20 May 2017, ISH heating HVAC industry event successfully held in Beijing International Exhibition Center. Fast boiler manufacture in sonipat latest on-line premix vacuum hot water boiler landmark "Thalia T6" and coupled steam boiler, "Euromonitor θ5" series of products also opened a mysterious veil, show it to all visitors.

Equipment maintenance method of a condensing gas boiler manufacture in sonipat, pressure maintenance 1. After condensing gas boiler shutdown the furnace all the water exhausted, the scale furnace, slag clean, rejoin qualified demineralized water. 2. Regular small flame, or periodically using water vapor adjacent to the boiler furnace, the furnace so that the water temperature in the summer condensing gas boiler should be maintained at about ambient temperature of + 10 ℃, winter should ensure that water does not freeze the furnace, close all vent valve, drain valve and drain valve, to prevent leakage. 3. Boiler feed water periodically to maintain the internal pressure of the condensing gas boiler 0.05MPa ~ 0.1MPa prevent air from entering the drum. Second, wet maintenance 1. After condensing gas boiler shutdown at the stipulated time exhausted furnace water, scale, slag, ash cleaned. 2. Close all manholes, hand holes, valves, etc., and the boiler is completely isolated. 3. Prepare a basic protection solution passing demineralized water, boiler water was added per ton of sodium hydroxide Na (OH) 8kg ~ 10kg, plus or sodium carbonate (NaC03) 20kg, plus or sodium (Na2P03) 20kg. 4. The formulated with special pump maintenance alkaline solution into the boiler. 5. When all of the resist solution is injected, the valve opened to fill the qualified demineralized water boiler, until the water overflows from the air valve, and then closing the air valve and the supply valve to open a dedicated pump cycle, a uniform mixed solution. 6. Throughout the maintenance should be periodically maintained with Weihuo drying oven outer heating surface, periodically turn the pump cycle, the concentration of the solution was consistent throughout, but also regularly take the solution assay and the replenishment solution, the PH value of the solution was ~ 10 between 12 to ensure that the alkalinity boiler water. 7. frost winter to take appropriate measures. Third, the dry gas condensing boiler maintenance 1. After shutdown, the boiler water exhausted, scale remove soot, slag and furnace heating surface. 2. Close condensing gas boiler water supply, water supply, the valve on the outfall, or blocked by the separator Yan, completely isolated from the other operation of the boiler. 3. Open the manhole, hand hole, the boiler dry naturally, if the boiler wet, with Weihuo the boiler and furnace wall flue drying. 4. The selection of an appropriate amount of desiccant. Common desiccant anhydrous calcium chloride (of CaCl2) and quicklime (CaO2), CaCl2 2kg per cubic meter of volume of water placed quantitative, requires selection of particles of about 15mm; lime 3kg per cubic meter of the volume of water placed quantitative, requires selection of 10mm ~ 30mm lumps. 5. condensing gas boiler drying, the tray containing a desiccant and the release drum furnace in order to absorb moisture, not in direct contact with the desiccant required boiler heating surface. 6. The desiccant should be checked regularly once placed, heating surface for corrosion to see, the desiccant is failed condensing gas boiler month per week, once a month later examination every two weeks.

Related Information