boiler supplier

ce certificate domestic oil fired hot water boiler

There are many kinds of steam boiler which can be applied in slaughterhouse, and slaughterhouse mainly uses steam boiler to generate high temperature steam and hot water to sterilization, disinfection and other usage. There are oil fired steam boiler, gas fired steam boiler, biomass fired steam boiler, coal fired steam boiler, CFB boiler can be applied in slaughterhouse. Compared to oil fired steam boiler and coal fired steam boiler, gas fired steam boiler is cheaper and more environmentally friendly, has lower requirement to the fuel compared to biomass fired steam boiler and CFB boiler.

Pressure fire operations and precautions Henan fast boiler's steam boiler Xiao Bian told you about the operation of steam boilers and pressure fire precautions and stainless steel high temperature magnetic pump structural characteristics 1. pressure steam boiler fire steps of (1) to reduce boiler load, according to the length of time of shutdown, the seam thicker, the thickness is generally not more than 200 mm, suitable to accelerate the speed of the grate. (2) to the slag is thickened seam about 1 mm from the stop grate rotation, the drum is stopped, the operation of the induced draft fan, blowing off a small segment of the regulating plate stopper and dampers qs, relying on natural ventilation to maintain coal the lean-burn, the sewage, boiler water level will rise to the maximum allowable level. If the fire burn coal gate, grate can be switched on again, the coal-fired back, a distance. (3) the recovery boiler needs to run, as long as the opening lead, a blower, to adjust the smoke, and the wind baffle plenum segment adjusting the opening degree of the shutter, the adjustment of combustion steam boiler seam thickness to be normal, start grate, can be restored run. 2. Note the use of a steam boiler (1) before starting Check power supply voltage, there are unusual circumstances water, close the drain valve opens the water supply valve, check whether the pump stuck, stuck if the pump, remove the fan cover, rotation of the motor shaft to the flexible state to boot. (2) When the steam boiler maintenance or replacement of parts, turn off the power to avoid live work dangerous. (3) electronic control box, pump motors and other parts should avoid damp water to prevent burning boiler should pay attention to keep clean. (4) steam boilers in accordance with quality requirements, when using the apparatus sure to install a water softener, the water softener is not used because the boiler may cause fouling, may cause serious squib, shortening the life of the boiler. (5) Please note that when using sewage. And at least once a day with a discharge pressure of between 0.1MPa to 0.15MPa discharge may be prevented clogging of pipes, sewage should be properly connected, to guard against burns. Stainless steel high temperature magnetic pump structural features: a sliding bearing magnetic pump sliding bearing materials impregnated graphite, PTFE and engineering ceramics. Because of engineering ceramics has good heat resistance, corrosion resistance, abrasion performance, so the sliding bearing magnetic pump more use of engineering ceramics production. Because of engineering ceramics are brittle and expansion coefficient, so the bearing clearance is not too small, so as not to hold the shaft accident. Since the magnetic pump in order to lubricate sliding bearing medium conveyed, it should be used depending on the medium and conditions, making use of different materials bearing. 2. Cooling lubricating fluid flow control pump operation must be flush cooling internal friction annulus region between the sliding bearing and the magnetic rotor and the containment shell with a small amount of liquid. Coolant flow rate is typically 2-3% of the design flow of the pump, the annulus area between the inner magnetic rotor of the eddy current generated spacer bush high heat. When enough cooling lubricant or flushing holes poor, clogging, the medium will result in a temperature above the operating temperature of the permanent magnet, the inner magnetic rotor gradually loses its magnetism, the magnetic force actuator failure. When the medium is water or water-based liquid, the temperature rise can be maintained in the annulus region of 3-5 deg.] C; or when the medium is a hydrocarbon oil, allows the annulus region of the temperature was maintained at 5-8 ℃. Henan is committed to fast boiler steam boiler manufacturing, product quality, reasonable prices and widespread industry praise, if you have any needs, please contact us!

Improve the thermal efficiency of the process wns gas boiler, oil-fired boiler which chemical incomplete combustion heat loss and mechanical incomplete combustion heat loss. Because almost no ash after combustion of the gas boiler, solid and liquid fuels without mechanical incomplete combustion, there is no need to consider the mechanical incomplete combustion of the gas boiler heat loss. In all heat losses, heat losses have tremendous proportions, when the high thermal efficiency of boilers, heat losses so the total loss of the main heat losses of fuel gas-fired boiler flue gas heat loss is the exhaust gas temperature and For air excess factor. When the exhaust gas temperature decreases, high thermal efficiency can be obtained, for example, a conventional three-pass steam boiler, furnace used in the past straight and smooth smoke tube, must increase the heating surface is arranged to make the exhaust gas to an acceptable degree, the theoretical discharge around the smoke heat loss. Potshell causing significantly increased diameter, wall thickness increased, greatly increased metal consumption, thus further reducing the exhaust gas temperature should be greatly restricted. From the aspect of heat transfer is not only now consider only the heated area, the use of new technology enables heat transfer performance significantly increased, the difference between the heat transfer overcomes the disadvantages of the past performance of the boiler, so that the exhaust gas temperature decreases, the structure is more compact. Center back boiler combustion boiler is preferably small foreign structure, although the two-pass boiler, the heated area is small, but the use of the turbulator charming, the purpose of enhancing the turbulence of the flue gas, disrupt laminar flow boundary wall, reducing the thermal resistance, increasing the heat transfer coefficient, a smaller heating area to achieve the same high thermal efficiency. Lower exhaust gas temperature limit in theory, the exhaust gas temperature can be reduced to very low or even close to the ambient temperature, for maximum thermal efficiency. However, in practice, due to the reduction of the exhaust gas temperature, low temperature corrosion will cause, therefore, the exhaust gas temperature can drop too low, in order to ensure that the wall temperature is higher than the main boiler heating surface flue gas dew point temperature. Therefore, low-temperature corrosion has become a major obstacle to reduce exhaust gas temperature and improve the thermal efficiency of the boiler. Tail auxiliary heating surface increases, further reducing the exhaust gas temperature, fuel gas wns improve thermal efficiency of the boiler as the oil, gas fuel burn easily wns type gas boiler air preheater generally not disposed. The economizer means is a common energy, which can be recycled flue gas was able to effectively reduce exhaust gas temperature. Separation type condensing gas boiler is out of the main boiler heating surface, the installation of the condensing heat exchanger. In one aspect of the flue gas absorption can significantly reduce the smoke temperature, reducing heat losses, on the one hand the absorption of part of the potential condensing water vapor released, increasing the effective use of heat of the fuel. Ash cleaning, to ensure that the heating surface of the scale wns boiler thermal efficiency of the boiler, the presence of soot fouling and heat transfer resistance increases, reducing the heat transfer effect. The thermal conductivity of the scale and soot is almost of the same order of magnitude, with the increase in scale, soot, the exhaust gas temperature rapidly increases, the thermal efficiency is significantly decreased. So, keep the boiler heating surface inside and outside clean, efficient heat transfer, thermal efficiency and to ensure the safe and economic operation of boilers, boiler fuel gas-fired boiler ash cleaning is required.

Henan miss you Jujube Industry Development Co., Ltd. is mainly engaged in dates, nuts and other healthy food research and development, procurement, production and sales operations; jujube industry's first listed company. I miss you date industry is committed to providing health and hygiene products for people to date, in 2017, I miss you date industry decided to buy a few new clean and green, can provide high-quality steam boiler steam. Carefully selected is determined in cooperation with the fast boiler, signed two separate 10 tons of steam condensing gas steam boiler (WNS10-1.25-Y.Q).

Related Information