poland build new generation chp with cfb boiler

Before regularly shutting down oil-fired poland build new generation chp with cfb boilers for inspection of electric furnaces, the following three aspects should be prepared:

Production technology and production technology side fast gas-fired poland build new generation chp with cfb boiler is very advanced, and our family has 200+ service centers throughout the country, as long as you need, we will arrive at the scene within 72 hours to help you out.

Note that, these condensing poland build new generation chp with cfb boiler cleaning errors occur frequently in many condensing boilers manufacture, transport and installation in a variety of situations will occur, so that the pipe wall boilers accumulate a large amount of dirt or other impurities in the oxide, resulting in the initial boiler run directly heating surface corrosion damage. To this end, boiler manufacturing companies will configure a set of operating instructions for each condensing boilers, including cleaning this one. Then the process consumers condensing boiler cleaning in which errors can strayed, how to avoid it? A chemical cleaning process does not detect the chemical analysis is a very rigorous chemical cleaning process. But if chemical cleaning is not complete, some dirt is not completely clean; and if the cleaning time is too long, there will be over-wash phenomenon; good cleaning effect, a secondary cleaning will waste of raw materials, and waste time. Which will increase the erosion had washed condensing boiler, condensing boilers metal pressure caused by a reduced ability of the normal operation of condensing boilers after impact. Improvements are: chemical analysis must be prepared to detect chemical cleaning processes, test once every tens of minutes acidity, total iron ion concentration, PH value. When two close data laboratory analysis, chemical cleaning end point is reached, and be discharged after reaching the neutral acid. Second, chemical cleaning is not performed after completion of the passivation process is the process of passivating the clean surface of the condensing boiler deactivators re reaction. Since the control point passivated more stringent requirements, if not properly controlled, the passivation will fail, and if the pickling is completed, and only a simple cleaning is finished, which makes the surface to be cleaned boiler condensate prone to two secondary rust, scale condensing boiler capacity decreases, prone to rust improvements: condensing boiler after pickling, passivation must be rinsed, since the passivation more stringent requirements, thus rinsing process must be strictly controlled total iron ions concentration. After rinsing is complete, iron ions tested meet the requirements, the PH value immediately adjusted to strongly basic, and the passivating agent is added, warmed passivation. It can be learned from the above, chemical cleaning condensing boiler there are more abnormal phenomena, and that the life of the condensing boiler, safe operation, energy production had a negative impact, therefore, in order to eliminate these abnormal phenomena, sustainable development and safe use of condensing boilers environment has a very big role.

March 19, 2019, Tangshan, Hebei Province, the city government official held "2019 Tangshan depth control key industries scientific and technological achievements Matchmaking" meeting the cement industry on air pollution emissions caps mobilization discussion. According to the news conference, Tangshan City Cement companies need before the end of September this year will be dust, sulfur dioxide, nitrogen oxides are controlled to not more than 10mg / m³, 30mg / m³, 50mg / m³. Official documents will be introduced in the near future.

It is reported, as early as in September last year, Tangshan cement industry in particular has a value of air pollutants emissions of nitrogen oxides emission concentration is less than 50mg / m³ proposed.

September 3, 2018, Tangshan Municipal Government issued the "ecological environment in Tangshan depth remediation tackling month action plan", "plan" industrial enterprises in pollution control, discharge of pollutants in the cement industry to make the following requirements: single production of raw grinding material, bag filter employed; one mill kiln production process, humidification tower may be used - electric precipitator dust collection system, dust emission concentration ≤10mg / m³. Rotary kilns for cement kiln and, preferably high dust coating, conditioning tower may be used - electric precipitator, dust emission concentration ≤10mg / m3, the concentration of sulfur dioxide emissions ≤50mg / m3, nitrogen oxides emission concentration ≤ 50mg / m3.