boiler supplier

power plant boiler with 10MW

Textile mill steam power plant boiler with 10mw water treatment method which currently boiler steam boiler is commonly used as a textile mill, used for disinfection, medicine and other suffering. For the pharmaceutical industry this particular area is concerned, the requirements for steam and hot water level is relatively high. This step treatment that becomes more important, the following small series bring you a quick look at the water treatment methods, results and so on. Simply put, the purpose of boiler water treatment is provided by the addition of certain equipment, such as impurity removal of boiler water softening treatment, prevention of boiler corrosion or fouling occurs, in order to ensure good quality of steam, but also conducive to the boiler thermal efficiency, in terms of the mill, which is more in need. Textile mill steam boiler water treatment method: (1) In general, when the boiler water treatment, taking into account their own situation, and the situation boiler boilers and other areas. Vapor pressure for evaporation and a small part of the boiler to be equipped with oxygen equipment in accordance with the actual situation, while the outer pot for the chemical treatment. (2) If the local water contains more impurities, water should be filtered before or during precipitation, so as to avoid blockage of the boiler water treatment equipment, water treatment effect is low, the efficiency is not high. (3) In addition, we should note that, during the boiler water treatment equipment selection, cut not covet low price, ease of use and other considerations while ignoring the quality of the equipment, so not only can not be effective treatment, but can also result in energy waste and reduce the life of the boiler. You know, for a long time corrosion and fouling it is easy to make low thermal efficiency of boilers, boiler unnecessarily severe accident. In short, this mill steam quality and environmental protection fields of high, must be strictly water treatment steps, in accordance with a qualified water treatment methods and standards.

To further promote the comprehensive management of coal-fired power plant boiler with 10mws, Jincheng City, Shanxi Province, according to "Jincheng Blue win the Battle of three-year action plan" requirements, plans to complete 109 units of 10-20 tons of steam "small coal-fired boilers" within this year the phase-out, at the same time, Jincheng will start working out of 35 tons of steam coal-fired boilers.

This year, Jincheng counties (cities, districts) the environmental sector will urge the relevant enterprises and institutions to eliminate the basis of 10 tons of steam and coal-fired boilers on in 2018 to accelerate the phase-out and 20 tons of steam coal-fired boilers. This year, the city to complete 109 units (10-20 tons of steam boilers) working out of a total of 589.5 tons of steam boilers; at the same time, Jincheng will also speed up the foundation and 20 tons of steam coal-fired boiler out, start 35 tons of steam phase out coal-fired boilers, in principle, within the city's new domain-wide 35 tons of steam coal-fired boilers.

In addition, Jincheng will accelerate the transformation of ultra-low emission. Before the end of September this year, the city will complete 52 units (65 tons of steam per hour and higher coal-fired boilers) coal-fired heating boilers ultra-low total of 4530 tons of steam boilers transformation, and the county (city) built-up area, biomass boilers emissions transformation. After transformation, under condition of the reference oxygen content of 6%, soot, sulfur dioxide, nitrogen oxides emission concentration of these boilers respectively not higher than 10 mg / m, 35 mg / m and 50 mg / m.

Transformation of low nitrogen in the combustion aspect, before the end of October, Jincheng station 610 will complete the transformation of low-nitrogen combustion Total 1940.15 tons of steam gas boiler, after completion of the transformation, the boiler NOx emission will not exceed 50 mg / m.

2. power plant boiler with 10mws, heating units lawful, it must be what license? Boilers, heating units for legitimate, it must have five licenses, namely: the heating unit to apply heat to run, then run by the relevant departments and heating the joint review, in order to build the boiler room by the review . After acceptance to issue a license heating, then, you can apply for a license fee.

Noun interpretation shell power plant boiler with 10mw shell type boiler basic structure is the double jacket structure. Called outer cylindrical boiler shell, called the inner furnace tube (fire tube), the space between the inner ring, an outer tube filled with water, and the inner cylinder combustion chamber. When the medium pressure vapor, by the internal pressure of the boiler shell, furnace subjected to external pressure. Shell boilers and discrete and horizontal. The most commonly used fuel, gas boiler WNS horizontal internal combustion shell boiler. Shell boiler has the following characteristics: 1, containing water "pot" and light a fire in the "furnace" are contained in a housing - housing pot; 2, metal hearth (furnace) a small volume, surrounded by water, cooled extent, poor combustion conditions, must burn the fuel quality; 3, less heating surface, heating power or a small amount of evaporation, often water or pyrotechnic means to increase the heating surface tubes and the boiler capacity; 4, potshell larger diameter casing, open more porous, irregularly shaped, it is connected to the inner portion of the heated portions together from heat, temperature and the degree of thermal expansion, and thus the security housing is poor; 5, the boiler system is relatively simple structure, easy to transport installation, maintenance and inspection operation management .

Related Information